The principle of a vacuum brewer was to heat water in a lower vessel until expansion forced the contents through a narrow tube into an upper vessel containing ground coffee. When the lower vessel was empty and sufficient brewing time had elapsed, the heat was removed and the resulting vacuum would draw the brewed coffee back through a strainer into the lower chamber, from which it could be decanted. The Bauhaus interpretation of this device can be seen in Gerhard Marcks' Sintrax coffee maker of 1925.
If all you’re looking for is a gorgeous cup of coffee and no fuss, we strongly recommend the Bonavita BV1900TS. It’s the smallest machine among our top picks and, at $190, the cheapest. Even better, it ranked in the top three out of 10 during our taste tests. It’s also the simplest and most straightforward: one button you click to start brewing, and that’s it. You can’t program brew times; you can’t play around with water temperature; and it even lacks some convenient touches like a brew basket that attaches to the machine (when you’re done brewing, you have to place the brew basket on a plate or in the sink before it makes a total mess). But it’s by far the fastest machine out of our top picks, brewing up a full eight-cup pot in under six minutes. It’s a straightforward, high-end coffee maker that leaves little to complain about.
An electric drip coffee maker can also be referred to as a dripolator. It normally works by admitting water from a cold water reservoir into a flexible hose in the base of the reservoir leading directly to a thin metal tube or heating chamber (usually, of aluminum), where a heating element surrounding the metal tube heats the water. The heated water moves through the machine using the thermosiphon principle. Thermally-induced pressure and the siphoning effect move the heated water through an insulated rubber or vinyl riser hose, into a spray head, and onto the ground coffee, which is contained in a brew basket mounted below the spray head. The coffee passes through a filter and drips down into the carafe. A one-way valve in the tubing prevents water from siphoning back into the reservoir. A thermostat attached to the heating element turns off the heating element as needed to prevent overheating the water in the metal tube (overheating would produce only steam in the supply hose), then turns back on when the water cools below a certain threshold. For a standard 10-12 cup drip coffeemaker, using a more powerful thermostatically-controlled heating element (in terms of wattage produced), can heat increased amounts of water more quickly using larger heating chambers, generally producing higher average water temperatures at the spray head over the entire brewing cycle. This process can be further improved by changing the aluminum construction of most heating chambers to a metal with superior heat transfer qualities, such as copper.
The impact of science and technological advances as a motif in post-war design was eventually felt in the manufacture and marketing of coffee and coffee-makers. Consumer guides emphasized the ability of the device to meet standards of temperature and brewing time, and the ratio of soluble elements between brew and grounds. The industrial chemist Peter Schlumbohm expressed the scientific motif most purely in his "Chemex" coffeemaker, which from its initial marketing in the early 1940s used the authority of science as a sales tool, describing the product as "the Chemist's way of making coffee", and discussing at length the quality of its product in the language of the laboratory: "the funnel of the CHEMEX creates ideal hydrostatic conditions for the unique... Chemex extraction." Schlumbohm's unique brewer, a single Pyrex vessel shaped to hold a proprietary filter cone, resembled nothing more than a piece of laboratory equipment, and surprisingly became popular for a time in the otherwise heavily automated, technology-obsessed 1950s household.
I have to say that I'm very happy that I waited for this one! The espresso is excellent, the drinks have all been hot (even when adding milk from the Aeroccino), the whole spinning process takes about 15 seconds (or less) to pour into the cup, and - most surprisingly - the new coffee-sized cartridges are AWESOME! They taste NOTHING like regular, ground grocery-store coffee-in-a-can. They are much more flavorful, much stronger, and seem fresher even than using whole coffee with a grinder (maybe it's from being sealed in the aluminum cartridges?)."
Drip-style coffee makers already have a bit of a flavor handicap when compared with other brewing methods, like pour-over and French press, which give coffee drinkers ultimate control over every aspect of the brewing (and therefore extraction) process. This makes it even more important to select a high-quality coffee bean for your at-home drip coffee maker. To learn more, we spoke with Saadat Awan at Woodcat Coffee in Los Angeles.
Breville's 12-cup Precision Brewer is stacked with features that allow you to fully customize your coffee, like adjustable brew temperature, bloom time, strength and more. It also has settings for making cold brew, iced coffee, or the Specialty Coffee Association's standard Golden Cup. It's beautifully designed thanks to its sleek brushed stainless steel exterior and LED-lit digital display. Just note that you'll have to spend time exacting your preferred settings, especially when you first set it up.
CR’s take: If you’re an aficionado of fresh ground coffee, this Black+Decker is the brewer to buy. As the name suggests, the Mill & Brew goes that extra mile, grinding whole coffee beans just before brewing. As a result, the machine is capable of making a great pot of coffee. Made of plastic with stainless steel accents, this model is easy to use and to clean, earning a Very Good rating in our convenience tests. It allows you to adjust brew strength, and it’s programmable, so you can set it to grind and brew just before you wake up.